Several issues to pay attention to when coating textiles
1. When connecting, please note that the cylinder number must be written on each head, so that the cylinder number can be determined according to the cylinder number when the coating is completed and inspected. Stacking them separately also allows the garment factory to cut them separately according to the cylinder number when cutting, thus avoiding color differences caused by fabrics with different cylinder numbers being made on the same piece of clothing.
2. When sewing the ends, pay attention to tearing the two ends evenly before sewing them together. If they are not evenly torn and then sewn together, it will cause a skewed weft.
3. Several issues should be paid attention to when applying machine coating:
1. Adjustment of tension: When coating, the tension should be adjusted according to different cloths. Uneven tension will cause uneven coating. , some places are thick and some are thin, and the feel will be uneven, some places are hard and some are soft.
2. Adjustment of the coating knife: When coating, different coating knives should be adjusted according to different coating requirements. One is the thickness of the knife. According to different requirements For the coating, you need to choose knives with different thicknesses. If you choose the wrong knife, you cannot guarantee the quality of the coating and cannot achieve the best coating effect. The other is to adjust the gap between the knife edges. The gap between the knife edges on both sides of the coating head should be the same, not one side is larger and the other is smaller. Otherwise, the coating will be uneven, and some products may even cause color differences on the left and right sides of the cloth, such as white or colored coating.
3. Cleaning of the cloth surface: It is actually the cleaning of the cloth surface during coating, because if there are lint or small particles on the coating surface during coating, Sand, these small things will get stuck in the coating edge, which will cause slivers on the coating surface and result in defective products. Therefore, before applying the knife, the cloth surface usually needs to be cleaned. The general solution is to install a brush in front of the painting knife, brush the threads and fine sand on the cloth, and at the same time sprinkle some water on the ground to maintain the air humidity so that the dust on the ground will not fly up and reduce the dust. Small static electricity adsorption. If a sliver is produced due to jamming at the blade edge, the operator must scrape it off as quickly as possible.
4. Temperature control of the drying room: The curing temperatures of coatings with different requirements are also different. Therefore, the temperature of the coating must be controlled. If the temperature is too high, it will feel hard and prone to blistering. If the temperature is too low, it will become sticky, have poor fastness, and fall off easily. Strictly speaking, the temperature of the drying room should be from low to high, usually from low to high for a three-stage drying room. The temperature of the first stage should not be too high. It should be controlled so that the boiling point of the solvent in the glue is slightly higher, so that the solvent in the glue can completely evaporate. If it is too high, the glue will start to solidify before the solvent has evaporated. Then after the second stage The remaining solvent in the drying oven will destroy the surface film, cause bubbling, and also cause the quality of the coating to decrease. For example, if a coating requires water pressure, destroying the coating film on the surface will destroy the water pressure. The temperature of the drying room in the third stage should be controlled at the curing temperature of the coating glue. If the temperature is low, the coating glue will not be completely cured and will become sticky, which will seriously affect the fastness. High temperatures will cause the hand to become hard and brittle. Destroy the physical properties of the coating glue.
5. Control of coating speed: Like the temperature above, the temperature and speed of the coating must be strictly controlled, which will directly affect the coating speed. layer quality. Because the curing of coating glue depends on two conditions, temperature and time. Although the temperature is controlled well, if the time is not controlled well, it will still affect the quality of the coating. Because two conditions are indispensable. Therefore, while controlling the temperature, you must also control the vehicle speed. If the speed is too fast and the curing time is not enough, it will still not be fully cured, which will also cause stickiness and peeling. If the speed is too slow and the time in the drying room is too long, the hand will become hard and brittle. Moreover, the production efficiency is low and energy is wasted.
6. When inspecting and packaging, pay attention to inspecting and marking in strict accordance with customer requirements. And stacked separately according to cylinder number. There should be clear signs and no confusion.
AAADBGRTHRTH
Disclaimer:
Disclaimer: Some of the texts, pictures, audios, and videos of some articles published on this site are from the Internet and do not represent the views of this site. The copyrights belong to the original authors. If you find that the information reproduced on this website infringes upon your rights, please contact us and we will change or delete it as soon as possible.
AA
